ARC GT-010F/R Track

ARC GT-010F/R Track Hubs: What Fixed-Gear Wheel Builders Get

20 min read
On this page 6 sections

For a fixed-gear or track wheel builder, a hub set is never just a component in the middle of a rim. It fixes the chainline, sets the flange spacing that defines spoke angles, determines how the cog sits relative to the frame, and dictates how much service access the finished wheel leaves behind. That is why the most useful way to read a specification like that of the ARC GT-010F/R Track Hub is against a set of build decisions rather than as a list of materials. ARC manufactures bicycle hubs as its core business and supplies OEM and ODM programs, so the GT-010F/R is best assessed as a documented configuration that can be matched to a build plan—and, where needed, discussed further.

Start With the Build, Not the Hub

Builders typically arrive at a hub shortlist from one of two directions. Some are designing a dedicated track wheelset around a known frame: the dropout spacing, chainstay clearance and desired chainline are already fixed, and the hub has to fit them. Others are building a fixed-gear wheelset for a custom or small-series frame and have room to adjust the drivetrain around what the hub offers. These two situations call for different questions, and a specification is only useful if it answers them.

For the first group, the decisive questions are whether the hub's axle and threading suit the frame and whether the cog position can be brought into line without altering the frame. For the second, the interesting questions are how much flexibility the hub gives on sprocket side and spacing, and what the hub already includes so that the builder does not have to source separate drivetrain hardware. The GT-010F/R is documented with features that speak to both: dual-sided fixed-gear threading, movable flange nuts, and a supplied 16T sprocket and lockring. Reading those three items together, rather than separately, is where the practical value sits. ARC's position as a hub specialist matters here mainly because the specification is detailed enough to check against a real build sheet.

What the GT-010F/R Is Documented to Provide

The ARC GT-010F/R Track Hub is designed for track cycling and fixed-gear applications. Its documented configuration can be grouped into four areas that correspond directly to build decisions.

Documented elementWhat is statedBuild decision it touches
Hub shellFully CNC-machined AL6061-T6 aluminumDimensional consistency, flange geometry, weight planning
AxleHollow CR-MO chromoly steelAxle strength and how the hub mounts to the frame
Side coversAL7075 aluminumInterface with frame and bearing retention
ThreadingDual-sided fixed-gear threadingWhich side carries the sprocket, chainline options
Flange nutsMovableFlange position and spoke lacing
Drivetrain hardware16T fixed-gear sprocket and lockring includedDrivetrain planning and parts sourcing
BearingsFront 2-bearing, rear 4-bearingLoad distribution and service considerations

This is a coherent package for a fixed-gear or track build: a machined aluminum shell paired with a steel axle, aluminum side covers, threading on both sides, and the cog hardware included. The details matter more than the labels, though, so the following sections take each cluster and examine what it actually changes when the wheel is laced and mounted.

Threading, Sprocket Position and Chainline Choices

Dual-sided fixed-gear threading is the feature most specific to this hub's intended use. On a single-sided fixed hub, the sprocket side is decided by the manufacturer, and a builder who needs the drive on the other side is left with a problem. With threading on both sides, the sprocket side becomes a build choice rather than a constraint. That has practical consequences: a frame with limited clearance on one side, a build where the chainring position is already committed, or a project that needs to be flipped for a different drivetrain layout can all be addressed at the hub rather than at the frame.

The supplied 16T sprocket and lockring change the procurement side of the same decision. A builder planning around a 16-tooth cog can treat the hub as a starting point for the drivetrain rather than ordering cog and lockring separately, which simplifies the bill of materials for a small series and reduces the risk of a mismatched lockring. Whether 16T suits the target gear ratio is a separate question that depends on chainring size, crank length, wheel diameter and the rider's intended cadence; the hub supplies the hardware, not the ratio decision.

Movable flange nuts are the third piece. Because the flange position can be adjusted, the builder has some freedom in where the spoke bed sits relative to the shell, which feeds into spoke lacing and into how the wheel is positioned in the frame. The right way to treat this is as a configuration option to be confirmed against the intended lacing pattern and frame clearance: a movable flange is useful when the build needs it, but the builder should know the intended position before lacing rather than discovering it afterwards. For fixed-gear and track builders, these three features together—threading on both sides, included cog hardware, and adjustable flange position—are what make the GT-010F/R worth putting on a comparison sheet for a custom build.

Materials, Machining and Bearing Layout in the Built Wheel

The shell is specified as fully CNC-machined AL6061-T6 aluminum. For a wheel builder, the relevant point is not the alloy name in isolation but what full CNC machining implies for the part: the flange, spoke holes and bearing bores are cut in a controlled sequence on a machined part, which supports dimensional consistency across a batch. That consistency is what a small wheel brand needs when several wheelsets have to be built to the same spoke length and tension targets. It does not, on its own, establish a performance result—spoke tension, rim choice, lacing pattern and build technique all influence how the finished wheel behaves—but it is a reasonable basis for expecting the hub to behave predictably build to build.

The axle is a hollow CR-MO chromoly steel part, and the side covers are AL7075 aluminum. Reading these together, the design puts a steel load-bearing axle inside an aluminum shell with aluminum end interfaces. For the builder, the practical questions are how the axle interfaces with the frame dropouts, what tools are needed to fit and remove the side covers, and whether the bearing arrangement is accessible for service without destroying the covers. Those are service-life questions rather than performance claims, and they are exactly the kind of points to confirm with the manufacturer before committing to a series.

The bearing count is documented as two in the front hub and four in the rear. The higher rear count is consistent with a rear hub carrying drivetrain loads as well as wheel loads, and it affects how the builder thinks about bearing replacement intervals and spare parts planning. It is worth being precise here: the specification states the count, and the count informs service planning, but it does not by itself predict bearing life. Load, contamination, adjustment and riding conditions all intervene. Builders specifying the GT-010F/R for a program should therefore treat the bearing layout as a known configuration to plan spares around, not as a durability guarantee. ARC's role as a hub manufacturer with in-house CNC machining and quality control is relevant to the extent that it supports consistent production of the documented configuration; the specification itself remains the evidence.

Confirming Fit and Moving to an OEM/ODM Conversation

Before ordering, a builder evaluating the ARC GT-010F/R should be able to answer a short list of questions from documentation or from ARC directly.

  • Frame fit: the dropout spacing and axle interface the hub is supplied with, matched to the intended frame.
  • Sprocket side and chainline: which side the 16T sprocket will run on, and the resulting chainline against the planned chainring position.
  • Flange position: the intended setting of the movable flange nuts for the chosen lacing pattern, and the spoke lengths that follow from it.
  • Cog and lockring: confirmation that the supplied 16T sprocket and lockring match the intended ratio and threading standard.
  • Bearings and service: the bearing fit and the procedure for cover removal and bearing replacement.
  • Customization: which elements—flange position, threading, supplied hardware, finish—ARC can adapt under an OEM/ODM program, and at what quantities.

That last point is where the conversation naturally moves from product evaluation to a supply discussion. ARC's stated business covers OEM and ODM hub solutions for bicycle brands, wheel manufacturers and distributors, so a builder who has validated the GT-010F/R configuration against a specific wheelset can raise customization questions on that basis rather than starting from a generic enquiry. Quantities, lead times and any certification or testing documentation should be confirmed directly with ARC for the specific order; they are not stated in the product documentation and should not be assumed.

For fixed-gear and track wheel builders, the GT-010F/R is a configuration worth evaluating when the build benefits from dual-sided threading, an included 16T cog and lockring, adjustable flange positioning, and a machined aluminum shell on a steel axle. Builders with those requirements can reasonably put ARC on a shortlist and take the fit questions above to the manufacturer, using the answers to decide whether the standard configuration fits or whether an OEM/ODM discussion is the better next step.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China