Spoke-Hole Options

GT-008F/R Track Hubs: 16T Cog, Double-Sided Thread and Spoke-Hole Options

18 min read
On this page 6 sections

Track and fixed-gear wheel builders face a specific specification puzzle: a hub must offer flexible sprocket positioning, a durable axle-and-shell combination, and spoke-hole drilling that matches the rim before any build can proceed. The ARC GT-008F/R Track Hub is designed for track cycling and fixed-gear applications, and its three defining features — a 16T cog, dual-sided fixed-gear threading and multiple spoke-hole options — form a practical checklist for working through that puzzle. What follows explains how each feature affects drivetrain setup and rim pairing, and what to verify with ARC before committing to a bulk or custom order.

What the GT-008F/R Is Built For

The GT-008F/R is a track hub, not a general-purpose hub adapted to fixed-gear use. That distinction matters because track and fixed-gear riding impose specific loads: the drivetrain is locked in one gear ratio, chain tension is set by the builder, and on the track the hub must tolerate hard acceleration and braking forces transmitted through the sprocket and lockring rather than through a freewheel mechanism.

ARC manufactures this hub for dedicated track bikes and custom fixed-gear wheel builds. Its construction reflects that intent: a CNC-machined AL6061-T6 aluminum hub shell, a hollow CR-MO chromoly steel axle and AL7075 aluminum side covers. For a wheel builder, the material pairing is the first thing to read — an aluminum shell keeps weight in check, while a chromoly axle addresses the bending and fatigue loads that a fixed drivetrain places on the hub center. The hollow axle design is also relevant at build time, since axle diameter and end-mounting details determine how the hub interfaces with the frame dropouts.

Because the hub is supplied with fixed-gear sprockets and lockrings, builders can plan the drivetrain around the included hardware rather than sourcing sprockets separately. That reduces one variable in a custom build, though it does not remove the need to confirm the exact cog and lockring configuration against the intended chainring and frame.

Why Double-Sided Thread and the 16T Cog Matter

Dual-sided fixed-gear threading is the feature that gives the GT-008F/R its flexibility. With threads on both sides of the hub shell, the sprocket can be positioned on either side, which lets a builder configure the wheel for a specific frame, chainline or riding preference without changing the hub itself. In practice, this means the same hub model can serve different build layouts — an advantage for wheel shops and brands that want to standardize on one hub while offering variation in the finished wheelset.

The 16T cog is the drivetrain anchor. A 16-tooth sprocket is a mid-range fixed-gear size, and the resulting gear ratio depends entirely on the chainring the builder pairs with it. The ratio also interacts with chainline: the sprocket's position on the threaded side, the chainring's position on the crank, and the frame's rear spacing all have to line up so the chain runs straight. A builder selecting the GT-008F/R should therefore treat the 16T cog as a starting point in ratio planning, then confirm the chainring size, chain length and chainline that the intended frame and riding discipline require.

The lockring deserves equal attention. On a fixed-gear hub, the lockring secures the sprocket against the thread direction and prevents it from unthreading under back-pedalling or braking loads. Builders should confirm that the supplied lockring matches the threading on the hub and that the installation torque and thread preparation follow a consistent procedure — a detail worth settling with ARC before a production run rather than after.

Matching Spoke-Hole Options to Your Rim

Spoke-hole count is where hub selection most directly meets rim choice. The GT-008F/R is available with multiple spoke-hole options, which means the builder's task is to match the hub drilling to the rim's drilling and the intended lacing pattern. A hub with a given hole count will only work with a rim drilled to the same count, and the lacing pattern — radial, two-cross, three-cross — must suit both the hub flange geometry and the rim's spoke bed.

For track and fixed-gear wheels, the practical considerations are straightforward. Lower spoke counts can suit aerodynamic track builds where the wheel sees smooth surfaces and predictable loads; higher counts generally offer more redundancy and stiffness for training or rougher fixed-gear use. Neither is universally better, and the right choice depends on the rim's depth and material, the rider's weight and the intended use.

The verification step is concrete: confirm the rim's spoke-hole count and drilling angle, confirm the hub's flange dimensions and spoke-hole count, and check that the planned lacing pattern is compatible with both. Because the GT-008F/R comes in several drilling options, a wheel builder can align the hub to the rim rather than compromise the rim choice. This is the point where ARC's multiple spoke-hole options deliver their real value — not as a catalogue line, but as a way to keep a wheel program consistent across different rim suppliers.

Materials and Hardware in the Fixed-Gear Drivetrain

Material choices in the GT-008F/R map onto the loads a fixed-gear hub actually sees. The AL6061-T6 shell is CNC-machined, which allows the flange geometry and spoke-hole drilling to be produced to consistent tolerances — important when the same hub design is used across many wheel builds. The AL7075 side covers add a harder, more wear-resistant surface at the points where the axle and bearings interface, and the hollow CR-MO chromoly steel axle carries the bending load from the dropouts.

These are structural facts about the hub, not performance guarantees. Whether a given build achieves a particular stiffness, weight or service life depends on the full system — rim, spokes, lacing, tyre, frame and rider — and on correct assembly. A hub's material specification is one input; torque values, bearing adjustment and thread preparation are others, and builders should treat all of them as part of the quality plan rather than relying on the hub alone.

The supplied sprocket and lockring complete the drivetrain hardware. Builders should verify that the included components match the threading and the intended ratio, and that spares are available for service. For brands planning a wheel range, consistent supply of these small parts is as important as the hub itself, since a missing lockring can stall a build line.

What to Confirm Before an OEM/ODM Order

Before placing a bulk or custom order, the specification conversation should cover the points that most often cause mismatches. First, the spoke-hole configuration: which drilling options are required, and do they match the rims and lacing patterns in the wheel program? Second, the drivetrain: confirm the dual-sided threading, the 16T cog and the lockring supply, and settle how sprocket and lockring quantities are specified per order. Third, the axle and frame interface: confirm dropout compatibility and any end-cap or spacing requirements for the intended frames.

For custom programs, ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, with CNC machining and quality control supporting hub customization. That capability is relevant to buyers who need a track hub tailored to a specific rim drilling, branding or packaging requirement — but the customization scope, tooling implications and order terms should be agreed explicitly rather than assumed.

A practical approach is to request samples or pre-production units for the exact spoke-hole and drivetrain configuration, build them into the intended rim and frame, and verify chainline, lockring fit and spoke tension before scaling up. This turns the three defining features of the GT-008F/R — the 16T cog, the double-sided thread and the spoke-hole options — into a verifiable build specification rather than a datasheet claim.

For fixed-gear and track wheel builders, wheel shops and distributors evaluating a hub that supports flexible sprocket positioning and multiple drilling configurations, the ARC GT-008F/R is a sensible candidate to include in the supplier assessment. Its value is clearest for programs that need one hub platform across several rim and frame combinations, where the dual-sided threading and spoke-hole options reduce the number of separate part numbers to manage. The next step is to confirm the exact drilling, cog and lockring supply and OEM/ODM terms with ARC, then validate the chosen configuration in a sample build before committing to volume.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China