ARC GT-010F/R Track

ARC GT-010F/R Track Hubs: What Fixed-Gear Wheel Builders Get

18 min read
On this page 6 sections

Fixed-gear and track wheel builders evaluate a hub on a different basis than road or mountain bike builders. With no freewheel and no derailleur, the hub must carry the chain tension, the braking load from backpedaling or a skid, and the alignment of a single sprocket position — all through a short, highly loaded assembly. The ARC GT-010F/R Track Hub is built around exactly this set of constraints: a CNC-machined AL6061-T6 shell, a hollow CR-MO chromoly axle, AL7075 side covers, dual-sided fixed-gear threading, movable flange nuts, a 16T sprocket with lockring, and 2 front / 4 rear bearings. What follows is a build-focused reading of that stated configuration — where each element matters when you are lacing a fixed-gear wheelset, and what a builder should confirm before specifying it.

Why Fixed-Gear Builds Ask Different Questions of a Hub

On a geared bike, the hub mostly holds the freehub body and lets the drivetrain do the work downstream. On a fixed-gear build, the hub is the drivetrain's terminus and its torque anchor. The chain is tensioned between chainring and sprocket with no slack-absorbing mechanism, so axle and shell interfaces see continuous alternating load rather than intermittent pedaling load. A rearward pedal stroke or a skid transfers force the opposite way through the same sprocket and threads, which puts the lockring and the threaded interface under repeated reversing stress.

That changes what a builder needs to know before lacing a wheel. The questions become: how is the shell machined and how consistent are the flanges; what axle material is used and how the axle is held in the frame; how the sprocket is fixed and whether the threading permits more than one chainline position; how many bearings share the load at each end; and whether the flange arrangement can be adjusted to suit different rim and lacing choices. The GT-010F/R answers each of these in its published specification rather than through marketing language, and that makes it straightforward to assess against a build sheet.

What the GT-010F/R Is Made Of

The shell is described as fully CNC-machined AL6061-T6 aluminium. For a wheel builder, the material and the machining method both matter: AL6061-T6 is a widely used structural aluminium with good machinability and predictable behaviour after heat treatment, and full CNC machining from billet typically allows tighter control of flange thickness, spoke hole spacing and bearing bores than a cast or minimally machined shell. The practical benefit at the build bench is a flange geometry that can be relied on when calculating spoke lengths and when checking that spoke heads seat consistently.

The axle is a hollow CR-MO chromoly steel unit. Chromoly is chosen here for the same reason it dominates track and BMX hardware — it tolerates high stress cycles and resists the deformation that repeated standing efforts and skid loads can impose on a rear axle. A hollow axle also allows the through-bolt or nut fastening arrangement to sit inside the axle rather than over it, which is a common layout on track frames with horizontal dropouts.

The side covers are AL7075 aluminium. This is a higher-strength aluminium grade than the shell material, and in a hub it typically serves the interface where the axle, bearings and frame contact meet. Whether that choice translates into any specific service life is not something the published specification claims; what it does indicate is that ARC has matched the cover material to a loaded interface rather than treating covers as cosmetic.

Threading, Sprocket and Flange Setup for Single-Speed Drivetrains

The defining feature of the GT-010F/R for fixed-gear work is its dual-sided fixed-gear threading. In practice, this means the hub can accept a sprocket on either side, which gives a builder a way to set chainline without changing the hub or the frame, and it opens the option of running a sprocket on one side with the other side available for a different ratio or a spare position. On a dedicated track bike this is mostly a chainline and gearing-flexibility question; on a custom fixed-gear street build it can also be a maintenance question, since the drive side can be moved without re-dishing the wheel.

The model ships with a 16T fixed-gear sprocket and a lockring. The inclusion of both is worth noting at the specification stage: a fixed-gear drivetrain needs the sprocket positively retained, and the lockring is the component that prevents the sprocket from unwinding under backpedaling and skid loads. Builders sourcing hubs as a set avoid the separate step of matching a sprocket and lockring to the hub's threading, and they know the included parts are intended to work together.

Movable flange nuts are the third element specific to this design. Their stated role is to allow flexible sprocket positioning and wheel-building configurations — in other words, the flange position on at least one side can be adjusted rather than fixed at the factory. For wheel builders this is a genuine planning input, because flange position drives spoke length, bracing angle and, at the rear, the dish. A builder who expects to move flange spacing should calculate spoke lengths against the intended final position rather than the as-delivered one, and should confirm with ARC which flange is adjustable and over what range before committing to a lacing pattern.

Bearing Configuration and Build Fit

The GT-010F/R is specified with two bearings at the front and four at the rear. The front count is a conventional layout for a track front hub. The rear count is the more interesting figure for fixed-gear builders: four bearings at the rear distribute radial and axial load across a wider base than a two-bearing rear hub, which is relevant where the hub sits between dropouts and carries the reversing loads described earlier. That said, bearing count alone should not be read as a durability or drag prediction. Bearing quality, seal type, grease fill, preload adjustment and the conditions of use all influence how a hub performs over time, and none of those are named in the published specification.

What a builder can reasonably take from the stated configuration is a starting point for verification: confirm bearing sizes and types, confirm whether the rear bearings are arranged to handle axial load from the sprocket side, and confirm the service procedure for replacement. For a wheel program, these are the questions that decide whether a hub belongs in a standard build or a premium one. The GT-010F/R, with a CNC shell, chromoly axle, AL7075 covers, dual-sided threading and a supplied sprocket and lockring, reads as a specification aimed at dedicated track and fixed-gear wheels rather than a general-purpose hub repurposed for single-speed use.

Specifying the GT-010F/R With ARC

For brands and wheelset builders evaluating this hub for a production or custom program, the useful next step is to work through the build sheet against the confirmed specification. Flange dimensions and adjustable range, axle length and dropout compatibility, threading standard, sprocket and lockring specification, bearing sizes and service parts — these are the items that determine whether the hub suits a given frame and lacing plan, and they are best confirmed directly rather than inferred.

ARC, operating as Taicang Xiangyue Sports Equipment Co., Ltd., is a bicycle hub manufacturer founded in 2013 and based in Taicang, Jiangsu, China, with in-house research, development, manufacturing and OEM/ODM customization for bicycle brands, wheel manufacturers and distributors. Because the GT-010F/R sits within that manufacturing scope as a track and fixed-gear model, buyers can raise build-specific questions — flange adjustment, axle configuration, bearing specification, sprocket and lockring supply — as part of an OEM/ODM discussion rather than as exceptions to a catalogue part. Details of the model are set out on the ARC GT-010F/R Track Bike Hubs product page, which is the right reference point for the current published configuration.

For fixed-gear and track wheel builders, the GT-010F/R is worth placing on the evaluation list when the requirement is a dedicated single-speed hub with dual-sided threading, an included sprocket and lockring, and an adjustable flange arrangement — and sample evaluation alongside a confirmed specification sheet is the sensible way to decide whether it fits a particular build program.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China