Bulk purchasing of 24H carbon-spoke MTB hub sets rewards preparation more than negotiation. The most reliable way to compare suppliers is to convert your wheel program into a fixed specification brief, then force every candidate hub set to answer the same line items: 24-hole front and rear drilling, flange geometry for carbon spokes, ratchet engagement, freehub and brake standards, Boost spacing, measured weight, and documented quality control. Suppliers that can respond to that brief with specific data—rather than general claims—are the ones worth shortlisting for samples. The ARC MT-116F/R 24H Carbon-Spoke Boost Center Lock MTB Hub Set is a useful reference point for how such a brief should be structured, because its published configuration covers the exact variables buyers need to pin down.
Define the Comparison Brief Before You Talk to Suppliers
Before requesting quotes, write down what the hub set must do inside your wheelset. A 24H carbon-spoke MTB hub set sits at the center of several dependent decisions: rim drilling, spoke type and lacing pattern, rider weight and discipline, brake standard, drivetrain standard, and frame spacing. Leaving any of these open invites suppliers to quote different products under the same description.
A practical brief should fix, at minimum:
- Drilling and layout: 24H front and rear, with the intended lacing pattern (for example, two-cross or three-cross) and the spoke count per side.
- Spoke interface: the carbon spoke brand and nipple type you intend to use, plus the spoke hole diameter and flange dimensions the hub must provide.
- Engagement: target points of engagement or ratchet tooth count, and whether the freehub mechanism is a serviceable, documented design.
- Standards: freehub body type (Shimano HG, Micro Spline or SRAM XD), brake interface (Center Lock or six-bolt), and axle spacing.
- Weight: a target figure and, critically, the measurement method—bare hub set, with or without end caps and quick-release or thru-axle hardware.
- Quality and customization: tolerances you will inspect, documentation you expect, and which parts (shell finish, laser marking, axle configuration) are open to OEM/ODM change.
Once this brief exists, comparison becomes mechanical. Every hub set is scored against the same columns, and gaps in a supplier's answer are visible immediately rather than discovered after a bulk order is placed.
Compare the 24H Configuration and Carbon-Spoke Fit
The 24H front and rear configuration is not simply a lower spoke count; it changes how load is distributed and how the wheel is built. With 24 spokes per wheel, each spoke carries a larger share of the load, so flange geometry, spoke hole placement and bracing angle matter more than in a 32H build. Buyers should ask for the actual flange diameter, flange spacing and spoke hole offset, then check that these figures suit the rim's drilling and the carbon spoke's specified bend or straight-pull interface.
Carbon spokes add their own constraints. They are typically less tolerant of sharp edges and incorrect hole angles than steel spokes, and their tensioning behavior differs. A hub intended for carbon spokes should present a clean, correctly angled spoke hole interface and a flange design that supports a balanced left-right layout. ARC describes its MT-116F/R as specifically engineered for carbon-spoke applications, with the 24H front and rear configuration supporting balanced spoke layouts and efficient wheel construction—the kind of statement that should be verified against drawings and a sample build rather than accepted on its own.
During comparison, ask each supplier three questions: what spoke hole diameter and chamfer they use, what lacing patterns they have validated with carbon spokes, and whether they can supply a sample hub set for a trial wheel build. A supplier who can provide drawings and a build recommendation is easier to qualify than one who only confirms "24H compatible."
Check Engagement, Standards and Spacing Line by Line
Engagement and interface standards are where nominally similar hub sets diverge most, so treat them as line items rather than marketing points.
Ratchet engagement. Tooth count affects the engagement angle and, in practice, how the hub feels under pedaling load. The ARC MT-116F/R is offered with 36T or 54T ratchet options and uses a patented one-piece ratchet architecture. For comparison purposes, the questions to ask are: what is the engagement angle at each tooth count, is the ratchet a single-piece design or a multi-part assembly, what material is used, and what service interval and spare-part availability apply. Tooth count alone does not establish durability or efficiency; it is one input among several.
Freehub standard. Confirm that the freehub body matches your drivetrain: Shimano HG, Micro Spline or SRAM XD. The MT-116F/R is listed as compatible with all three, which matters for brands building one hub platform across several groupset tiers. Ask whether the freehub body is interchangeable within the same hub shell and what the swap procedure involves.
Brake interface. Center Lock is the stated interface on the MT-116F/R. Verify rotor compatibility, lockring type and clearance with your intended frame and rotor size.
Spacing and axle. The MT-116F/R uses 15×110mm front and 12×148mm rear Boost spacing. Confirm this matches your frame standard and that end caps are included and replaceable; the product specifies AL7075 aluminum end caps alongside the AL6061-T6 shell and AL7075 axle and freehub body.
Weight. The quoted figure of approximately 340.1g is a useful comparison datum, but only if every supplier weighs the same configuration. Ask whether the figure includes end caps, and request a measured weight from the sample you receive.
Validate Samples, Tolerances and Quality Documentation
Catalog data gets a supplier onto the shortlist; a sample build gets them onto the order. Before committing to bulk, build at least one wheel with the candidate hub set using your intended rim and carbon spokes, then evaluate:
- Spoke hole and flange fit: no play, no galling, and correct spoke angle at the flange.
- Bearing feel and preload: smooth rotation without detectable lateral play after the axle is torqued to specification.
- Freehub engagement: consistent pickup across the ratchet, no skipping under load, and acceptable sound level for your market.
- Dimensional checks: hub width, flange spacing and disc mount alignment measured against the drawing, not just against a nominal standard.
- Finish and marking: shell finish quality, laser marking accuracy and consistency between front and rear.
Alongside the sample, request the documentation your quality plan requires: dimensional inspection reports, material certificates for the AL6061-T6 shell and AL7075 axle and freehub body, and the supplier's own in-process inspection routine. Agree on the acceptance criteria in writing—what tolerance band applies to critical dimensions and what happens if a production lot falls outside it. This is also the moment to confirm the measurement method behind the quoted weight, since a stated figure without a defined method is not a comparable specification.
Ask the OEM/ODM Questions That Shape the Bulk Order
The final stage of comparison is commercial and operational, and it should be asked before pricing is finalized. For a 24H carbon-spoke MTB hub set, the relevant questions include:
- Customization scope: which elements can be changed—shell color and finish, laser marking, axle configuration, ratchet tooth count, freehub specification—and which are fixed by the platform design?
- Engineering support: can the supplier review your wheel build parameters and recommend flange and lacing details, or provide drawings for your product engineers to sign off?
- Configuration control: how are revisions tracked, and will you be notified before a change affects a part you have approved?
- Sampling and approval flow: what is the process from sample to approved production, and what evidence closes each stage?
- Spare parts and after-sales: availability of ratchet components, freehub bodies and end caps for the life of your product.
ARC, based in Taicang, Jiangsu, manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors, covering MTB, road, gravel and e-bike applications. For a buyer assembling a comparison shortlist, that positioning is relevant because the MT-116F/R platform already addresses the 24H carbon-spoke, Boost, Center Lock and multi-standard freehub requirements that dominate this category. The hub set is a sensible candidate to include when your brief calls for those specifications and you want a supplier able to discuss customization rather than only catalog variants.
The shortlist that emerges from this process should be small—typically two or three suppliers who answered every line of the brief, supplied a buildable sample and agreed on tolerances and documentation. Ordering in bulk then becomes a confirmation of work already done, not a leap of faith. If your program centers on 24H carbon-spoke MTB hub sets with Boost spacing and flexible freehub standards, the ARC MT-116F/R is worth putting through this exact comparison, starting with a sample build and a written tolerance agreement.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China