Why Fixed-Gear and Track Builds Ask Different Questions of a Hub
A track or fixed-gear wheelset is not a road wheelset with a single cog bolted on. Because the drivetrain has no freewheel, every pedal input—and every attempt to slow the bike by resisting the pedals—passes through the hub, the sprocket interface and the axle. A hub that feels adequate on a geared bike can become the weakest point of a fixed-gear build if its threading, locking arrangement or axle material were chosen for lighter, intermittent loads. That is the context in which the ARC GT-010FA/RA Track Hub Set deserves attention: it is specified around fixed-gear and track use rather than adapted from a road platform.
For builders and component buyers, the practical question is rarely "which hub is strongest." It is whether a given hub's shell material, axle specification, cog retention, threading layout and drilling match the frame, rim, chainline and rider load the wheelset is being built for. Each of those choices narrows or widens what the finished wheel can do, so they are worth settling before a sample is requested, not after lacing has begun.
What the GT-010FA/RA Hub Set Provides
The ARC GT-010FA/RA Track Bike Hubs are built around a fully CNC-machined AL6061-T6 aluminum hub shell, paired with a high-strength AL7075 aluminum axle and matching components. In a fixed-gear context, that combination matters for two reasons. The machined shell gives the flanges and bearing seats a controlled, consistent form, which is the foundation for even spoke tension and predictable bearing alignment. The AL7075 axle addresses the other end of the load path: because a fixed drivetrain can apply torque in both directions, axle strength and stiffness are not cosmetic details.
Cog retention is handled by an integrated locking structure with stainless steel locking hardware. On a fixed-gear bike the sprocket is loaded whenever the rider accelerates, skids or brakes through the pedals, so a secure, mechanically simple lockring arrangement is central to drivetrain reliability. ARC supplies a 16T fixed-gear sprocket and lockring with the set, which means the builder receives the cog interface and its retention hardware together rather than sourcing them separately and hoping the threads and lockring shoulder agree.
The hub set uses double-sided fixed-gear threading, so a sprocket can be positioned on either side of the hub. Drilling is 20H at the front and 24H at the rear, and the set is offered with S&S steel bearing options. ARC states a total weight of approximately 512 g for the set. That figure should be read as a stated nominal weight for the hub set, not as a claim about the finished wheel or about durability—those depend on rim choice, spoke count, build quality and riding conditions.
Matching the Hub Specification to Your Wheel Build
The 20H front and 24H rear drilling is the first specification to reconcile with the rim. Twenty-four holes at the rear is a relatively low count, which suits rims designed for lower spoke numbers and riders whose priority is a stiff, aerodynamic track wheel rather than maximum redundancy. If the intended rim is only offered in 28H or 32H, this hub set is the wrong starting point regardless of its other merits. Builders should confirm rim drilling, spoke type and lacing pattern together, because a 24H rear wheel leaves little margin for creative cross patterns.
Double-sided threading is often described as a convenience, but its real value is chainline flexibility. A frame with an unusual chainstay clearance or a builder targeting a specific chainline can choose which side carries the sprocket, then verify that the resulting chain line and lockring clearance work with the crank and frame. It is worth measuring rather than assuming: the cog position, the lockring stack and the frame's dropout width all interact.
The included 16T sprocket also sets an expectation about gearing. Sixteen teeth is a common starting point for track and fixed-gear builds, but the final ratio depends on the chainring and the rider's cadence targets. Buyers should treat the supplied sprocket as a baseline component and confirm whether their program requires a different tooth count, since sprocket availability and lockring compatibility are separate questions from hub specification.
Bearing choice is the remaining variable. S&S steel bearings are the stated option for this set; buyers with specific rolling-resistance, maintenance-interval or sealing requirements should raise those expectations explicitly during the specification conversation rather than infer them from the bearing designation alone.
Sourcing the GT-010FA/RA Through ARC's OEM/ODM Model
The specification questions above are exactly the kind that are easier to resolve with the manufacturer than with a catalogue. ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd. and based in Taicang, Jiangsu, China, has focused on bicycle hub research, development, manufacturing and customization since 2013. Its stated work covers OEM and ODM supply for bicycle brands, wheel manufacturers and distributors, supported by CNC machining, precision manufacturing and quality control systems. For a track or fixed-gear program, that positioning is relevant because hub specification—drilling, threading, axle material, bearing selection—is where a wheelset program either fits its frame and rim ecosystem or does not.
A sensible next step for a brand or wheel builder evaluating the GT-010FA/RA is to prepare a short specification brief: intended frame dropout spacing, rim drilling and model, target chainline, required sprocket tooth count, bearing preference and expected rider load. Presenting those points together lets ARC respond on the specific configuration rather than on the hub set in general, and it gives the buyer a clear basis for deciding whether to request a sample or move to an OEM/ODM quotation. Buyers should also confirm at that stage which elements are fixed in the standard set and which fall within ARC's customization scope, along with sample lead times and order terms—details that are best verified directly rather than assumed.
For fixed-gear and track wheel builds where a machined aluminum shell, an AL7075 axle, double-sided threading, a supplied 16T sprocket and lockring, and 20H/24H drilling all align with the intended frame and rim, the ARC GT-010FA/RA is a hub set worth placing on the evaluation list. The decisive work is confirming that the specification matches the build—and ARC's hub-focused OEM/ODM operation is set up to answer those questions at the component level.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China