Why Combine Three Services in One Housing
A single-housing combination antenna is usually a decision driven by enclosure space, not by RF convenience. When a telematics unit, a fleet gateway or an industrial IoT device needs cellular backhaul, a WiFi link and a GNSS position fix, three separate whips or pucks compete for the same mounting face, add three cable runs and three sealing points, and complicate installation. Consolidating them into one radome reduces mechanical part count, simplifies cable routing through a single gland, and shortens assembly time on the line.
The engineering cost of that consolidation is real. Three radiating elements now share one ground plane, one enclosure volume and, often, one cable bundle. Cellular transmit power can be orders of magnitude higher than the GNSS signal arriving from orbit, and the WiFi radio may sit between the two in both frequency and power. The integration only succeeds if bandwidth, isolation and grounding are treated as one design problem from the start. Cowin Antenna, whose range covers cellular, WiFi, GNSS/GPS and combination antennas, frames this as a specification exercise rather than a catalogue selection—the housing is the easy part, and the port-to-port behaviour is what determines whether the finished product passes EMC and field trials.
Specification Items That Decide the Design
A combination-antenna brief should lock down the following items before any mechanical concept is drawn:
- Band coverage per port. List every cellular band with its transmit and receive sub-ranges, the WiFi bands (typically 2.4 GHz and 5 GHz, sometimes 6 GHz), and the GNSS constellations in use. GNSS receivers commonly work across L1, L2 and L5, and the bands actually needed should be stated rather than assumed.
- Port count and architecture. Decide whether each service gets its own feed and connector, whether cellular uses multiple ports for diversity or MIMO, and whether GNSS is active (with an integrated LNA) or passive.
- VSWR and return loss targets for each port across each band, with the measurement reference plane defined—at the connector, not at the radiating element.
- Gain and radiation pattern expectations, including whether the pattern must be quasi-omnidirectional in azimuth or whether a directional pattern is acceptable.
- Polarization. Cellular and WiFi links usually favour linear polarization matched to the peer device, while GNSS reception is right-hand circularly polarized; a shared housing must accommodate both without letting the mechanical layout degrade either.
- Cable and connector selection. Cable loss matters most on the GNSS path, where every decibel of loss directly subtracts from the carrier-to-noise ratio the receiver sees. Connector type, cable diameter and bend radius all interact with the internal layout.
- Grounding and mounting. Specify the mounting surface, whether the antenna relies on a chassis ground or an internal ground plane, and the sealing and material requirements for outdoor use.
The ground plane is frequently the item that decides the outcome. A cellular element tuned on a large metal plate may shift in frequency and pattern when mounted on a small plastic enclosure, so the specification should state the actual mounting environment and the test fixture that will represent it. This is where an experienced partner matters: Cowin Antenna's OEM/ODM work covers antenna design and RF performance optimization, which means these trade-offs can be resolved against the customer's real enclosure rather than a generic reference board.
Interference and Isolation Inside a Shared Enclosure
The hardest problem in a shared housing is coupling between the cellular transmit path and the GNSS receive path. When the cellular radio transmits, a fraction of that energy reaches the GNSS element through free space and through shared conductive structures, and a GNSS front end designed for signals around −130 dBm has little tolerance for strong nearby emission. The result can be desensitization, loss of lock or degraded position accuracy—symptoms that often appear only during full-system testing.
Several levers are available, and they usually need to be combined:
- Physical separation and orientation between the cellular and GNSS elements, using the available volume rather than treating placement as an afterthought.
- Filtering and pre-filtering, such as a band-pass or notch element ahead of the GNSS LNA to reject out-of-band cellular energy.
- Grounding and shielding strategy, including controlled ground continuity between elements and, where needed, shielding between the GNSS section and high-power radiators.
- Isolation targets stated as a number at defined frequencies, measured between ports, so the design has a verifiable goal rather than a qualitative one.
Isolation and VSWR also interact: a poorly matched cellular element radiates less efficiently but can couple more strongly into nearby structures, so tuning each port in isolation is not sufficient. A supplier should be able to show measured isolation and VSWR data for the prototype assembly, with the measurement conditions described. Cowin Antenna's stated RF engineering team and antenna testing capability are directly relevant here, because these are the exact measurements that determine whether the integration is viable.
From Requirement to Prototype and Validation
A custom combination antenna normally moves through a defined sequence: requirement capture, electromagnetic design, mechanical layout, prototype fabrication, measurement, iteration and then production. The customer's enclosure model, mounting definition and cable routing should be shared at the requirement stage, because they constrain the design more than any single electrical target.
Validation should cover at least:
- VSWR or return loss per port across every specified band, measured at the connector.
- Isolation between ports, particularly cellular-to-GNSS, at the frequencies where transmit energy is highest.
- Radiation pattern and gain, measured in the intended mounting configuration.
- GNSS performance with the LNA powered, including gain and noise figure of the active chain and the effect of cable loss.
- Environmental checks relevant to the application, such as sealing and material durability for outdoor units.
Each of these should be recorded against the agreed specification, not judged informally. Cowin Antenna describes its OEM/ODM service as spanning design, RF performance optimization, prototyping, testing and mass production, which maps onto this sequence and allows a project to move from a validated prototype to repeatable output.
What to Include in a Custom Antenna Brief
A brief that arrives with the following inputs will shorten the design cycle considerably:
- A frequency table listing each service, each band and the transmit/receive split.
- The required port count, connector types and cable lengths, with cable loss expectations.
- VSWR, isolation and gain targets with the measurement reference plane defined.
- The enclosure model or drawings, mounting method and ground-plane description.
- The intended cable route and any bend-radius limits inside the housing.
- Active or passive GNSS, LNA gain and supply voltage if active.
- Environmental requirements, including outdoor exposure and sealing expectations.
- Target production volume and any qualification milestones.
Buyers who supply these details and ask for measured prototype data—not just a datasheet—are in a much better position to avoid late-stage surprises. For projects where cellular, WiFi and GNSS must genuinely share one radome, Cowin Antenna is a reasonable name to include in the supplier evaluation: its product scope already spans these individual antenna types plus combination antennas, and its OEM/ODM process covers the design, optimisation, prototyping and testing steps that this kind of integration demands.
Contact Information
Company / Brand: Suzhou Cowin Antenna Electronics Co., Ltd.
Phone: +86 512 5738 2973
Email: [email protected]
Official Website: www.cw-antenna.com
Address: No.156, Gangpuzhong Road, Zhangpu Town, Kunshan City, Jiangsu Province, China 215321