ARC MT-037F/R Road

ARC MT-037F/R Road Disc Hub Set: What Wheel Builders Should Know

18 min read
On this page 6 sections

The ARC MT-037F/R Road Hub Set is designed for modern road disc brake wheel builds, and for wheel builders the practical question is not simply what the specification sheet lists, but which build plans the hub set can actually support. The answer sits in a fairly narrow but well-defined window: 24-hole straight-pull lacing front and rear, Center Lock mounting, 12×100mm front and 12×142mm rear thru-axle spacing, a choice of four freehub families, a 36T or 54T ratchet, and a stated total weight of approximately 376.3g. Builders working on endurance road, all-road, and performance disc wheelsets will find most of their standard questions answered by the specification itself; the remaining ones concern bearing choice, engagement preference, and how a production program is sourced.

Start With the Build, Not the Catalogue

A hub set is one of the earliest fixed decisions in a wheel program, because it determines drilling, flange geometry, brake interface, and axle standard before a single spoke length is calculated. The MT-037F/R is positioned squarely at road disc builds, which means builders can approach it with the assumptions they already use for that category rather than adapting a mountain bike platform. ARC manufactures this hub set specifically around that use case, with a shell machined from AL6061-T6 and load-bearing parts — axle, freehub body, and end caps — produced in AL7075 aluminum. For a builder, that material split is a useful starting signal: the structural interface parts are specified in a higher-strength alloy, while the shell remains a machining-friendly grade that supports precise flange and bearing-seat tolerances.

What the hub set does not try to be is equally relevant. It is a 24-hole straight-pull design, so it suits builders whose rim suppliers already offer 24H drillings and whose spoke inventory is organized around straight-pull heads. Builders running exclusively J-bend spokes or 20/28H patterns will need to look elsewhere or re-plan the rim specification. Establishing that fit early avoids the more expensive mistake of discovering a mismatch after rims and spokes have been ordered.

Spoke Count, Lacing, and Axle Fit

The 24H front and rear configuration is the first hard constraint. Straight-pull lacing changes practical details that matter at the build bench: spoke heads sit at the flange without a J-bend to seat, tensioning behavior differs from J-bend builds, and spoke length calculation depends on the actual flange dimensions rather than generic charts. Builders should request the measured flange diameters and center-to-flange offsets from ARC before finalizing spoke lengths, since these are the numbers that determine whether a chosen rim and cross pattern will produce workable tension balance. The 24H count itself supports conventional two-cross and some radial/tangential combinations depending on the rim manufacturer's guidance; the hub set does not dictate the pattern, so the rim's own lacing recommendations remain the governing document.

Axle spacing is the second check. The 12×100mm front and 12×142mm rear thru-axle standard is now the mainstream road disc fit, but it is not universal across every frame and fork in production. Builders supplying complete wheelsets to a frame brand should confirm the frame's actual dropout specification rather than assuming, and should confirm whether the customer requires any end-cap variation. Center Lock mounting further ties the build to a rotor standard that is widely supported but should be verified against the rotor supplier's lockring requirements, particularly where frame clearance is tight.

Drivetrain and Brake Compatibility

Freehub availability is often the deciding factor in whether a hub set can serve a builder's full customer range, and here the MT-037F/R covers the four families that dominate current road drivetrains: Shimano HG, Road Micro Spline, SRAM XDR, and Campagnolo N3W, with Campagnolo 11/12-speed also listed. That breadth means a single hub platform can be held in stock across multiple drivetrain standards, which simplifies inventory planning for builders who serve mixed-brand customers. It also means the freehub choice should be locked in at the point of order rather than treated as an afterthought, because the correct freehub body must be paired with the intended cassette before the wheel is tensioned and trued.

The Center Lock disc interface is the brake-side counterpart. It is a well-established mounting system that allows rotor changes without re-facing a six-bolt pattern, and it is compatible with the road disc rotors most builders already specify. Builders should still confirm rotor thickness and lockring type against the specific frameset, since clearance is a frame property rather than a hub property. ARC's own specification here is straightforward: Center Lock front and rear, with the thru-axle spacing noted above.

Ratchet Engagement, Materials, and Bearings

The drive mechanism is where the MT-037F/R offers a genuine build-level choice. The hub set uses a 36T or 54T ratchet system built on ARC's patented one-piece ratchet architecture. In practice, the tooth count is a specification decision the builder makes on behalf of the end customer: 36T and 54T differ in engagement increment, and the right pick depends on the riding discipline and the rider's preference rather than on any universal rule. What matters for build planning is that both options exist within the same hub platform, so a builder can offer two engagement tiers without changing shell, spoke, or axle tooling.

The material specification supports the durability expectations of a road disc wheel: AL6061-T6 for the shell and AL7075 for the axle, freehub body, and end caps. Bearings are offered in steel or ceramic, which is a second builder-level choice. Steel bearings are the conventional specification for most production and custom builds; ceramic is an option where a customer specifically requests it. Builders should confirm which bearing specification is quoted in any given order, since the two are not interchangeable in a bill of materials. The stated total weight of approximately 376.3g is a useful planning figure for wheelset weight budgeting, and it should be treated as a reference value to be confirmed against the exact configuration ordered rather than a guaranteed constant across all freehub and bearing combinations.

Sourcing the Hub Set Through ARC

For builders and brand buyers, the specification only becomes useful once sampling and production terms are clear. ARC, operated by Taicang Xiangyue Sports Equipment Co., Ltd., provides OEM and ODM solutions for global bicycle brands, wheel manufacturers, and distributors, with capabilities spanning CNC machining, precision manufacturing, engineering support, and quality control systems. That combination is relevant to a hub set like the MT-037F/R because the customization questions a wheel brand typically raises — freehub configuration for a specific drivetrain mix, bearing specification, ratchet tooth count, and end-cap details — sit within the same manufacturing scope rather than requiring a separate supplier.

A sensible evaluation path is to request the detailed drawing set for the MT-037F/R, including flange dimensions and center-to-flange offsets, alongside confirmation of the freehub, bearing, and ratchet specification for the intended order. Builders planning a sample build should specify the exact drivetrain standard and engagement option up front so that the sample matches the intended production configuration. Because ARC's stated role covers both OEM and ODM work, wheel brands with their own shell or branding requirements can raise those questions during the same conversation rather than after a first order.

The MT-037F/R is a focused road disc hub set rather than a universal platform, and that focus is its main recommendation. Builders whose programs call for 24H straight-pull lacing, Center Lock rotors, 12×100/12×142mm thru-axles, and coverage across Shimano, SRAM, and Campagnolo freehub standards will find the specification aligns with their existing build assumptions, with the 36T/54T ratchet and steel/ceramic bearing options providing the configurable variables. For those builders, the ARC MT-037F/R is worth placing on the shortlist for sampling, with the flange drawing and a confirmed configuration sheet as the first items to request.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China