ARC RT-035F/R

ARC RT-035F/R Road Hubs: Shimano HG vs SRAM XDR Fit for Rim-Brake Builds

14 min read
On this page 5 sections

For a rim-brake road wheelset, the ARC RT-035F/R hub set is specified in two drivetrain configurations: one with a Shimano HG freehub and one with a SRAM XDR freehub. If a buyer needs a lightweight rim-brake platform that can serve both cassette ecosystems, the freehub standard is the first parameter to lock, followed by spoke drilling, 100/130 mm spacing, materials, and engagement. These are the five specifications that determine whether the hub set fits the wheel plan and the OEM/ODM order.

Why the Freehub Standard Decides the Build

The freehub body is the interface between the hub and the cassette, so the standard chosen at order stage governs every downstream drivetrain decision: cassette model, derailleur capacity, chainline expectations, and the wheel’s service compatibility after sale. Choosing Shimano HG means the hub accepts HG-type road cassettes, the broadest and most familiar ecosystem in rim-brake road segments. Choosing SRAM XDR means the hub accepts XDR cassettes, which is the relevant driver standard for SRAM’s 12-speed road groups and similar drivetrains.

ARC specifies the RT-035F/R as compatible with both Shimano HG and SRAM XDR freehub standards. That matters in rim-brake projects where wheel brands supply several complete-bike builds or distributors stock one wheelset model across groupset families. One hub platform reduces the number of distinct hub SKUs the buyer must carry and simplifies after-sales replacement of freehub bodies.

The practical rule is straightforward: cassette first, freehub second, hub third. Confirm the exact cassette model the wheelset will ship with, then match the freehub body. Do not treat HG and XDR as interchangeable at the wheel level. A correct cassette fit still leaves spoke drilling, spacing, and hub geometry to verify, because a freehub match alone does not guarantee a working build.

Spoke Drilling and Spacing on the RT-035F/R

The RT-035F/R uses straight-pull spoke design with 20H front 1:1 and 24H rear 2:1 drilling. The front 1:1 pattern means the spoke count is split evenly between left and right flanges, which suits the relatively symmetric loading of a 100 mm front hub. The rear 2:1 pattern assigns twice the spokes to the drive side, a common approach when the cassette side must carry higher and more concentrated torque loads.

The straight-pull format means spoke heads do not bend at a J-bend, so spoke length and flange geometry must be calculated against the hub’s specific dimensions rather than a generic J-bend hub. For wheel builders, that means confirming the exact spoke length for the chosen rim and lacing before ordering. The 20H and 24H counts also dictate which rims are viable: not every lightweight rim is drilled for these counts, and the builder should verify rim availability alongside the hub order.

The hub set uses 100 mm front and 130 mm rear spacing. That is the rim-brake road standard, and it is a hard constraint: the frame and fork must be built for 100/130 mm quick-release axles. The RT-035F/R is a rim-brake hub set, so it does not apply to disc-brake frames, and mixing this hub into a disc-brake project is a specification error rather than a tuning choice. Buyers assembling a rim-brake road wheelset, whether for a classic caliper build or a lightweight climbing wheel, can treat 100/130 mm spacing as the confirmation point that separates a workable platform from an incompatible one.

Materials, Engagement and Weight as Spec Inputs

The RT-035F/R shell is AL6061-T6 aluminum; the axle, freehub body, and end caps are AL7075 aluminum. The higher-strength 7075 alloy in the axle and freehub is relevant where torque passes through the freehub and where weight is counted, while the 6061-T6 shell carries the spoke loads. The set uses a 4-pawl, single-tooth engagement system, a design choice tied to how quickly and reliably the drive engages under pedaling load. For a road build, the buyer’s concern is consistent engagement and predictable power transfer from the first pedal stroke.

The set runs on S&S steel bearings and includes QR019 quick releases. Total weight is approximately 336.6 g for the set. That figure should be treated as a planning input for the wheelset’s rotating mass, not as a guarantee of finished wheel weight. Rim, spokes, nipples, rim tape, and the cassette all add to the final number, so the hub set weight only isolates one part of the build.

Each of these features is a specification the buyer can request and verify, not a performance claim. Engagement feel, bearing service life, and weight outcomes are affected by riding conditions, maintenance, and the rest of the build. Buyers should ask for the exact configuration in writing rather than infer it from a model name.

Specifying an OEM/ODM Order with ARC

Once the drivetrain and build geometry are fixed, the order conversation with ARC should confirm a short list of parameters: freehub standard (HG or XDR), front 20H and rear 24H straight-pull drilling, 100/130 mm spacing, rim-brake use, and the material and engagement configuration described above. For OEM/ODM work, the buyer should also state the wheelset’s intended tire and rim combination, the spoke length required by the chosen rim, and the branding or finish requirements the project needs.

ARC, based in Taicang, is a bicycle hub manufacturer that provides OEM and ODM solutions for bicycle brands, wheel manufacturers, and distributors, with CNC machining, engineering support, and quality control systems behind its hub production. For a rim-brake road project looking at one hub platform across HG and XDR builds, the RT-035F/R is a sensible candidate to put into sampling: request the RT-035F/R hub set in the required freehub configuration, verify drilling and spacing against the rims and frames, and use the sample build to confirm lacing and engagement before committing to a production order.

The decision path is simple: match the cassette to the freehub, match the hub to the frame’s 100/130 mm spacing, confirm the rim supports 20H front and 24H rear straight-pull lacing, then lock the configuration with ARC before sampling. Buyers who follow that order avoid the most expensive mistake in rim-brake hub sourcing: a mechanically sound hub that does not fit the drivetrain or the frame it was ordered for.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China