Custom Wheel Builds

How to Choose a CNC Fixed-Gear Track Hub for Custom Wheel Builds

25 min read
On this page 6 sections

A CNC fixed-gear track hub is rarely a simple drop-in decision. For a custom wheel build, the hub must match the frame's spacing, the rider's drivetrain and gearing, the rim's spoke plan, and the load intended for track or street use. Getting any of these wrong usually surfaces only after the wheel is laced and installed. The most reliable approach is to set criteria first, then compare hubs against those criteria, and only then brief a supplier for samples or a quotation.

This buyer-side checklist turns hub specification into build-fit and supply decisions. It also shows where a manufacturer such as ARC becomes relevant: ARC builds bicycle hubs with CNC machining and offers OEM/ODM customisation, and its GT-002FR CNC track hub is a concrete example of how fixed-gear-specific features can be assessed against a wheel plan.

Start from the build, not the spec sheet

The first step is to define what the wheel has to do before opening any catalogue. Three inputs drive most hub requirements: rider use, frame interface, and wheel plan.

Rider use determines the load case. A track hub used for sprint efforts faces different demands from one used on a street fixed-gear for commuting and tricks. Gearing also matters: a rider running a large chainring with a small rear cog puts different torque through the sprocket and hub body than a rider using lower gearing.

Frame interface sets the hard constraints. Rear spacing, axle type and dropout shape must all match the hub. A hub that is dimensionally correct but offers the wrong axle standard will not fit without adapters or frame work, both of which add cost and risk.

Wheel plan defines the spoke side. Spoke count, rim drilling, intended lacing pattern, and tyre and rim width all interact with hub flange geometry. A 32-hole rim cannot take a 28-hole hub, and a rim designed for two-cross lacing may sit poorly with a hub whose flange dimensions suit radial or one-cross patterns.

A practical way to run this step is to write a short build brief before comparing products:

  • Rear spacing and axle standard required by the frame
  • Intended gearing and whether the rider wants a fixed-only or flip-flop setup
  • Spoke count, rim drilling and planned lacing pattern
  • Expected rider weight and use case, track or street
  • Whether the wheel is a one-off custom build or one line in a production run

That brief becomes the checklist every candidate hub is measured against. It also prevents the common mistake of choosing a hub because it looks precise, then discovering the spoke count or threading does not serve the build.

Shell, axle and machining: what CNC actually buys you

CNC machining is often treated as a quality label in itself. In practice, it is a process that can deliver tighter dimensional consistency and cleaner features, but the value depends on the material and the design it is applied to.

On a fixed-gear track hub, the shell and axle are the structural core. The shell carries the spoke flanges and houses the bearings, so its machining accuracy influences bearing alignment and spoke hole position. The axle carries the load through the dropouts and must resist bending and fatigue. Material choice and heat treatment matter as much as the machining method.

The ARC GT-002FR illustrates how these elements are specified together: a fully CNC-machined AL6061-T6 hub shell combined with a high-strength AL7075 aluminium axle, freehub components and end caps. AL6061-T6 is a familiar choice for hub shells where machinability and strength need to balance, while AL7075 is used in the axle and related components for higher strength.

For buyers, the practical lesson is to ask not only whether a hub is CNC-machined, but what is machined and to what tolerance. Useful questions include:

  • Which components are machined, and which are formed or cast and then finished?
  • What material and temper are used for the shell and axle?
  • How are spoke holes positioned and deburred, and how is bearing seat alignment controlled?
  • Are end caps and axle components matched to the intended frame spacing?

These points connect directly to build fit. Accurate spoke hole placement supports consistent spoke tension, and clean bearing seats reduce the risk of premature bearing wear. Neither guarantee a particular service life on its own, because bearing quality, spoke tension, rim choice and riding conditions all contribute, but they are reasonable indicators of manufacturing care.

Weight and durability sit on the same scale here. A lighter hub shell can improve acceleration feel, but material and wall thickness must still carry the rider's load. For track use the trade-off may favour stiffness and precision, while street fixed-gear builds may place more weight on impact resistance. There is no universal right answer, only a fit between the hub's construction and the intended use.

Sprocket mounting and threading decisions

Fixed-gear drivetrains impose loads that freewheel hubs do not see, because the rider can resist and reverse torque through the chain. Sprocket mounting is therefore one of the most important fixed-gear-specific choices.

The conventional arrangement uses a threaded hub body with a sprocket threaded onto it, secured by a lockring. Thread direction and quality matter: a poorly cut thread can allow the sprocket to work loose or sit off-centre, and cross-threading during installation damages the hub body. Buyers should confirm the threading standard and check that the sprocket and lockring engagement is clean and full-depth.

An integrated locking structure is another approach. The ARC GT-002FR uses an integrated locking structure and double-sided fixed-gear threading, which supports secure sprocket installation and flexible setup options. The double-sided threading is relevant for riders or builders who want to run different gearing on each side, or who want a flip-flop style setup within a fixed-gear configuration. The hub is supplied with a 16T fixed-gear cog and lockring, so a build can be specified as a complete hub set rather than sourcing the cog separately.

For custom wheel builders, the questions to settle are:

  • Which threading standard does the hub use, and is it compatible with the intended cog and lockring?
  • Is the locking structure integrated, and how is the lockring secured?
  • What cog size is supplied, and what range is appropriate for the intended gearing and chain length?
  • Is the hub fixed-only, or does the threading arrangement allow a different setup on each side?

Gearing choice deserves a check against the whole drivetrain. The supplied 16T cog is a starting point, but chainstay length, chainring size and intended cadence determine whether it suits a particular rider. Builders should confirm the final gear ratio before the wheel is laced, since changing the cog later is easy but changing the hub is not.

Spoke count, flange geometry and lacing fit

The hub is only half of a wheel, and spoke compatibility is where many custom builds fail. Before ordering, match the hub's spoke drilling to the rim's drilling, then confirm flange geometry suits the intended lacing pattern.

Spoke count is the simplest check. A hub drilled for 28 spokes cannot serve a 32-hole rim, and mismatched counts usually mean replacing a component. Beyond count, flange diameter and flange spacing affect spoke angle and bracing. Larger flanges generally shorten spokes and can stiffen the wheel, while widely spaced flanges improve lateral bracing. The right combination depends on the rim depth, rider weight and intended use.

Lacing pattern is the third variable. Radial lacing on a fixed-gear rear hub is unusual because the hub must transmit drive and braking torque through the spokes; cross patterns distribute that torque more evenly. Builders should confirm the hub's spoke holes are suitable for the planned cross count and that the flange thickness accommodates the spoke heads and elbows without binding.

A practical verification sequence is:

  1. Confirm hub drilling matches rim drilling.
  2. Calculate spoke length from the hub's flange dimensions and the rim's effective diameter.
  3. Check the planned lacing pattern against the hub's intended use and torque direction.
  4. Confirm spoke head and elbow clearance on the flange.

For custom builders, asking the supplier for the hub's flange dimensions, spoke hole diameter and any lacing recommendations is a reasonable request. A supplier that can provide these figures promptly is easier to work with during sampling, and a hub whose geometry is documented clearly reduces the risk of a wheel that needs relacing.

What to ask a hub supplier before sampling

Criteria are only useful if the supplier can meet them consistently. Before committing to samples or a production order, buyers should turn their build brief into a set of verification questions and use the answers to compare suppliers.

Specification and tolerance. Ask which dimensions are controlled and how they are inspected. For a CNC hub, spoke hole position, bearing seat alignment, axle diameter and thread quality are the key items. Request the flange dimensions and threading standard in writing so they can be checked against the build brief.

Material and component traceability. Confirm the shell and axle materials, and whether end caps and axle components are supplied as a matched set. On the GT-002FR, the AL6061-T6 shell and AL7075 axle, freehub components and end caps are specified together, which makes it easier to discuss the hub as a complete assembly rather than a collection of parts.

Sprocket and cog configuration. Confirm what is supplied with the hub, including the cog size and lockring, and whether alternative cog sizes or threading arrangements are available. This matters for OEM programmes where the final gearing may differ by model.

OEM/ODM scope. For brands and wheel manufacturers planning a production run, ask what customisation is possible and what the sampling process looks like. ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, which means the discussion can move from a catalogue hub to a specification tailored to a particular wheel programme. Buyers should clarify which elements can be customised, what information the supplier needs to quote, and what the sample approval steps are.

Quality documentation and inspection. Ask what inspection records accompany samples and production batches. A supplier with a defined quality control process should be able to describe how hubs are checked before shipment. Buyers should treat specific claims about testing standards or failure rates as items to verify rather than assume.

ARC's position in this process is as a manufacturing partner rather than a catalogue-only seller. Founded in 2013 and based in Taicang, Jiangsu, ARC focuses on bicycle hub development, manufacturing and customisation, with CNC machining and quality control supporting OEM and ODM work. For a fixed-gear or track wheel programme, the GT-002FR is a relevant reference point: its fully CNC-machined AL6061-T6 shell, AL7075 axle and components, integrated locking structure, double-sided fixed-gear threading and supplied 16T cog and lockring give buyers a concrete specification to test against their build brief.

The right choice for a custom wheel build is the hub that satisfies the build brief on spacing, threading, spoke plan and intended use, and whose supplier can document and repeat those characteristics. Builders and OEM buyers who set those criteria first, then request samples and a quotation against them, are in a stronger position to compare CNC fixed-gear track hubs on fit and supply rather than appearance alone. ARC's CNC track hub range and OEM/ODM capability make it a supplier worth including in that evaluation for fixed-gear and track wheel projects.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China