Why Freehub Standard and QR Spacing Must Be Decided Together
When a bicycle brand or wheelset builder prepares a mountain bike hub specification, the freehub standard and the quick-release spacing are often handled as separate line items—the freehub chosen from the cassette side, the spacing taken from the frame drawing. In practice, they jointly decide whether the finished wheel can be installed, indexed and ridden without rework. A hub with the correct freehub body but the wrong dropout spacing will not sit in the frame; a hub with the right 9×100 mm front and 10×135 mm rear spacing but an incompatible cassette interface will accept the frame yet reject the drivetrain.
The reason these two decisions belong in the same specification step is that both are fixed at the point of hub selection. Freehub interface determines which cassette families can be mounted; quick-release spacing determines which frame dropouts the hub will fit. Changing either after the hubs are ordered means new parts, new sample rounds or a revised frame drawing. Locking both before committing to a purchase order is far less costly than correcting them later. It also keeps the rest of the specification stable: spoke count, rotor mount and axle details are usually confirmed once the freehub and spacing envelope are settled, because these parameters must work within the same hub geometry.
For entry-level and recreational MTB programs, this is especially relevant, since frames in this segment commonly use conventional quick-release dropouts rather than thru-axles. Getting the pairing right the first time protects development schedules and keeps sample builds aligned with production intent.
Selecting the Freehub Interface for the Intended Cassette
The freehub body is the mechanical bridge between the hub shell and the cassette. Three interface families dominate current MTB drivetrains: Shimano HG, Shimano Micro Spline and SRAM XD. The selection should follow the cassette the bike program will actually use, not a general preference for one brand.
The HG interface is the long-established splined standard and remains common on entry-level and recreational builds, where wide-range cassettes with conventional splines are specified. Micro Spline uses a different spline pattern and is tied to Shimano's newer MTB cassette families. SRAM XD uses a threaded interface designed for XD cassettes. Each interface has its own body geometry, so a hub cannot be converted between them by changing a cassette—the freehub body itself must match.
Before ordering, the specification should record the exact cassette model, its interface family and the number of speeds planned. It should also confirm that the hub's stated freehub compatibility covers that family, rather than assuming one interface fits all. Where a product is offered in more than one freehub version, the version code must appear on the purchase order so that the supplied hubs match the drivetrain, not just the shell colour or spoke count.
Verifying 9×100 mm and 10×135 mm Quick-Release Dropouts
Quick-release spacing is measured across the frame dropouts: 100 mm at the front and 135 mm at the rear for the conventional MTB standard. These figures describe the frame, not the hub alone, so verification should start from the frame drawing or a physical measurement of the dropout faces. A hub supplied as 9×100 mm front and 10×135 mm rear will only fit a frame built to those dimensions.
Two checks are worth building into the process. First, confirm the dropout spacing on every frame size and variant in the program, since a single frame platform can have revisions. Second, confirm the axle and end-cap configuration that accompanies the quick-release system, because the hub's axle type and end caps must match the dropout and the quick-release skewer supplied. For programs still using rim or cable-actuated disc brakes alongside disc hubs, the rotor mount should be checked at the same time as the spacing, as both are set by the frame and brake layout.
This verification should be completed before the hub order is placed, not during the sample build. If the frame drawing and the hub specification disagree on spacing, the frame is the harder item to change—so the hub specification should be adjusted to the frame, within the available product options.
Completing the Specification: Spoke Count, Brake Mount and Axle Details
Once the freehub interface and QR spacing are fixed, the remaining parameters should be confirmed against the wheel build plan. Spoke count is the first: 28H, 32H and 36H options serve different rim designs and riding demands, and the chosen count must match the rim drilling and the intended build. A specification that lists "32H or equivalent" without a firm choice can produce mismatched rims and hubs.
The brake interface follows. A 6-bolt disc mount must match the rotors and brake system planned for the build; where the frame and fork use a different mount type, this should be resolved at the hub level rather than with adapters chosen later. Spoke type should also be recorded—J-bend spokes require hubs designed for J-bend heads, and the hub's flange geometry must suit the lacing pattern.
Axle and end-cap details complete the picture. Material and construction specifications, such as an aluminium axle with steel end caps or a specific alloy grade, should be captured as stated by the supplier so that the purchase order reflects the actual configuration. These details do not usually change after the freehub and spacing are fixed, but they should be confirmed in the same document to avoid partial orders or substitute parts arriving at the wheel-building stage.
Using the ARC MT-001FG/003RC as a Reference Configuration
The ARC MT-001FG/003RC 32H 6-Bolt QR MTB Hub Set shows how these decisions come together in a single specification. ARC, based in Taicang, Jiangsu, manufactures this set for entry-level and recreational mountain bike wheel builds, with a J-bend spoke design, a 6-bolt disc brake interface and availability in 28H, 32H and 36H configurations. It is compatible with Shimano HG, Micro Spline and SRAM XD freehub standards, so the freehub version can be selected to match the intended cassette family rather than forcing the drivetrain to fit the hub.
On the spacing side, the set features 9×100 mm front and 10×135 mm rear quick-release spacing, which aligns with conventional QR dropout frames common in this segment. The set includes the QR001 MTB quick-release system, so the axle and end-cap configuration arrives with the hubs rather than as a separate item to source. The hub shell uses AL6061-T6 aluminium, with an AL7075 aluminium axle and freehub body and CR-MO end caps, and the reinforced 6-pawl, 3-tooth engagement system is stated at 120-point engagement.
For a brand or wheelset builder preparing a specification, this set is a useful reference because the freehub options and the QR spacing are both declared and can be checked against the cassette and frame drawing before ordering. Buyers can then confirm the spoke count and the 6-bolt rotor mount against the rim and brake plan. Where a program needs a different configuration, ARC's OEM/ODM customization services provide a route to discuss the hub specification directly with the manufacturer.
The practical next step is to fix the cassette interface and the dropout spacing in one specification document, record the spoke count and rotor mount, and request a matching configuration—using the ARC MT-001FG/003RC as a starting point where its freehub and spacing options fit the frame and drivetrain.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China