ARC MT-037F/R Road Disc Hub

What Wheel Builders Get from the ARC MT-037F/R Road Disc Hub Set

15 min read
On this page 6 sections

Wheel builders evaluating a hub set for a road disc program rarely need another catalogue page. They need to know whether a specific hub will accept the drivetrain, axle, spoke and rotor interfaces their builds already use, and whether the supplier can hold those choices consistent across production. The ARC MT-037F/R road disc hub set answers that question directly: it is a 24H straight-pull, Center Lock hub set with 12×100 mm front and 12×142 mm rear thru-axle spacing, a choice of five freehub standards, steel or ceramic bearings, and 36T or 54T ratchet engagement.

Start With the Build, Not the Hub

For a wheel builder, a hub set is a commitment across several dependent decisions. Spoke count and lacing format determine the drilling, the spoke type and the build sequence. Axle spacing determines whether the hub fits the frames and forks in a given program. The rotor interface determines which disc rotors can be mounted. And the freehub standard determines which drivetrains the finished wheelset can serve. Getting any one of these wrong is not a cosmetic issue; it can invalidate a batch build or force a separate hub variant.

ARC's MT-037F/R is configured around the conventions most road disc programs already use. The hub set runs 24 spokes front and rear in a straight-pull format, mounts Center Lock rotors, and uses 12 mm thru-axles at both ends. Each of those choices narrows the range of components a builder must verify, and each should still be checked against the intended rim, spoke and frame specification before an order is placed.

Freehub Standards a Builder Can Specify

The freehub body is often the single largest source of part-number proliferation in a wheelset line. The MT-037F/R covers the main road and gravel drivetrain families through a choice of freehub standards: Shimano HG, Road Micro Spline (MS), SRAM XDR, Campagnolo N3W, and Campagnolo 11/12-speed.

The practical value for a wheelset brand is that one hub platform can be specified across several drivetrain programmes rather than sourcing a different hub family for each. A builder producing wheels for Shimano HG road groups, SRAM XDR-equipped bikes, and Campagnolo builds can keep the same hub shell, axle and bearing architecture in the bill of materials and treat the freehub as a variant. That reduces the number of distinct hub drawings a builder has to manage and simplifies spare-part planning.

The freehub choice should still be confirmed at the order stage, because the freehub body is a machined part matched to the hub and the correct standard must be stated explicitly. Builders should also confirm the intended cassette and chainline requirements against the chosen freehub rather than assuming interchangeability between standards.

Lacing, Axle Spacing and Rotor Mount

The 24H front and rear straight-pull configuration is the structural foundation of the set. Straight-pull spokes are laced without a J-bend, which changes how the spoke is captured at the flange and how the builder plans spoke length and tensioning. ARC describes the 24H configuration as supporting efficient spoke integration and balanced wheel construction, and for a builder the operative point is that spoke selection should be planned around a straight-pull hub rather than adapted from a J-bend build sheet.

The 12×100 mm front and 12×142 mm rear thru-axle spacing matches the current road disc standard, so the hub set is intended for frames and forks built to that specification. A builder should verify the axle standard and rotor clearance against the actual frame and fork drawings for each model in the programme, since a hub that fits one road frame is not automatically suitable for every frame in a range.

Center Lock is the rotor interface. It uses a splined mount secured by a lockring rather than six bolts, which affects rotor selection and the tools required at assembly. Builders specifying this hub set should confirm that the rotors and lockrings in their component list are Center Lock compatible and that the lockring type suits the axle end.

Ratchet and Bearing Choices

The drive mechanism is a ratchet system offered in 36T or 54T, built on what ARC describes as a patented one-piece ratchet architecture. The two tooth counts represent different engagement characteristics, and the choice belongs to the builder or brand based on the ride feel and application the wheelset is intended to deliver. ARC does not publish comparative performance figures for the two options here, so the selection should be made from the intended use case and confirmed with ARC rather than inferred from the tooth count alone.

Bearings are offered in steel or ceramic. This is a specification choice that a builder can align with the position of the wheelset in a range, and it should be stated at ordering so the correct bearing set is fitted. The complete hub set is quoted at approximately 376.3 g, a figure worth carrying into the wheelset weight budget alongside rim, spoke and nipple weights rather than treated as a standalone specification.

The hub shell is precision-machined from AL6061-T6 aluminium, with the axle, freehub body and end caps in high-strength AL7075 aluminium. For a builder, the material specification matters mainly as a consistency question: the same shell and axle architecture should carry across the freehub and bearing variants so that build fixtures, spoke lengths and assembly procedures remain valid across the range.

Where ARC Fits as a Supply Partner

ARC, operating as Taicang Xiangyue Sports Equipment Co., Ltd., manufactures bicycle hubs and provides OEM and ODM solutions for bicycle brands, wheel manufacturers and distributors. That supply relationship is the relevant one for a wheel builder sourcing a hub set: the MT-037F/R is not a single fixed SKU but a platform whose freehub standard, ratchet tooth count and bearing type are specified by the buyer.

For a wheelset brand planning a road disc line, this means the MT-037F/R can be evaluated as one hub platform across multiple drivetrain variants, with the configuration choices fixed at the sample and order stage. Builders should prepare a specification sheet covering freehub standard, ratchet tooth count, bearing type, spoke count and lacing, axle spacing and rotor interface, and confirm each item with ARC before committing a batch. Requests for samples or OEM/ODM discussion should be framed around that specification so the supplied hubs match the build plan rather than a default configuration.

The MT-037F/R is a sensible starting point for builders whose road disc programmes sit on 12×100/12×142 thru-axles, Center Lock rotors and 24H straight-pull lacing, and who want one hub platform to cover Shimano HG, Road Micro Spline, SRAM XDR and Campagnolo freehub requirements. Confirming the freehub, ratchet and bearing specification with ARC early is the step that turns that fit into a workable supply arrangement.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China