Carbon spokes change the rules of wheel construction, and the change lands hardest at the hub. A spoke that is stiffer in tension, has a different elongation profile and often presents a bonded or molded end rather than a conventional threaded nipple asks the hub to control load paths, spoke angles and interface fit far more precisely than a steel-spoke build does. In practice, that means a general-purpose hub adapted to carbon spokes is a compromise, while a hub designed around them is a starting condition for a build that can be repeated, serviced and scaled into production.
For wheel program managers, the practical question is not whether carbon spokes are attractive in a lightweight MTB wheelset—they clearly are—but whether the hub sitting at the center was specified for them. ARC, a Taicang-based hub manufacturer serving OEM and ODM programs, frames its MT-116F/R Boost Center Lock hub set around exactly this premise: a 24H front and rear configuration engineered for carbon-spoke applications and balanced spoke layouts. The design reasoning behind that positioning is worth unpacking, because it gives specifiers a checklist to apply to any hub under evaluation.
Why a Carbon-Spoke Build Starts at the Hub
With metal spokes, the hub has some tolerance for approximation. Steel spokes stretch measurably under tension, build processes can take up small inconsistencies through tensioning and stress-relieving, and a spoke hole that is slightly off-angle often still produces an acceptable wheel. Carbon spokes behave differently: they are stiff, they resist elongation, and their end fittings are typically bonded or molded rather than swaged. The result is that errors at the hub interface do not quietly disappear during tensioning. They translate into uneven tension, off-axis loads at the spoke end and a wheel that is difficult to bring into true and keep there.
There is a second difference that matters just as much: spoke angle at the flange. Carbon spokes generally do not tolerate sharp bends or contact with a flange edge in the way a steel spoke can. The path from the spoke hole to the rim needs to be clean, and the bracing angle has to be set deliberately by the flange geometry rather than corrected after the fact. A hub whose flange positions and spoke hole angles were drawn for steel spokes may impose a path that a carbon spoke end cannot comfortably follow.
This is why the hub, not the rim or the spoke alone, decides whether a carbon-spoke program is buildable and serviceable. A hub purpose-engineered for carbon spokes accounts for the spoke interface, the flange layout and the load transfer into the shell from the first drawing. ARC's MT-116F/R is presented as engineered for carbon-spoke applications rather than adapted to them, which is the distinction buyers should be probing in every supplier conversation.
Spoke Count and Layout: The 24H Front and Rear Question
Spoke count on a carbon-spoke MTB wheel is a balancing act. Fewer spokes support the lightweight objective, but each spoke carries a larger share of the load, so the hub must distribute that load predictably across the flange. A matched front and rear count makes that distribution easier to reason about, because the builder is working with a consistent pattern rather than compensating for different counts at each end.
The MT-116F/R uses a 24H front and rear configuration, which ARC states supports balanced spoke layouts and efficient wheel construction. The practical value for a program manager is repeatability: matched counts simplify lacing documentation, spoke length planning and the tension targets the build team works to, and they make it easier to compare prototype builds against each other. On a carbon-spoke wheel, where the spokes contribute significantly to lateral stiffness, a consistent layout is also a way to keep ride feel and handling predictable across sizes.
Two questions are worth asking of any 24H carbon-spoke hub. First, whether the flange geometry was drawn for the specific lacing patterns the program intends to use, including two-cross and three-cross options if both are planned. Second, whether the spoke hole positions and angles keep the carbon spoke end seated cleanly under target tension. A supplier that can answer both from the design file, not just from a sample, is a better partner than one that answers only after a build fails.
Interface, Flange and Material Choices That Carry the Load
Carbon spokes transfer load into the hub differently from steel, and the shell, axle and freehub have to be specified with that in mind. ARC builds the MT-116F/R around a precision-machined AL6061-T6 aluminum hub shell with a high-strength AL7075 aluminum axle, freehub body and end caps. The material split is a familiar one in performance hubs—AL6061-T6 for the shell, where machinability and toughness matter, and AL7075 for the axle and freehub, where strength-to-weight is the priority—but the relevant point for a carbon-spoke program is that these are defined, stated components rather than unspecified ones.
Flange design deserves the closest reading. On a carbon-spoke wheel, the flange diameter, spoke hole offset and the spacing between flanges together set bracing angle and therefore lateral stiffness and spoke tension balance. A flange that is generous enough to spread load but shaped so the spoke exits without a kink is the goal. Specifiers should ask for the flange drawing, the spoke hole angle, and confirmation of which spoke end fittings the hub is designed to accept—then check that against the carbon spoke supplier's own interface requirements, because the two are a system.
The freehub body matters for a different reason. Carbon-spoke wheels are often built for performance riding, where drivetrain loads are high and engagement feel is part of the product. The MT-116F/R uses a 36T or 54T ratchet system with ARC's patented one-piece ratchet architecture. Engagement tooth count is a drivetrain interface decision, not proof of overall wheel performance—buyers should treat it as one specification among several and confirm it suits the intended riding category.
Specification Checklist Before You Sample
Sampling is expensive, and a carbon-spoke program that reaches the sample stage with a mismatched hub burns time in both directions. The checklist below reflects the points a buyer can verify against published hub data and supplier confirmation before committing tooling or order quantities.
- Spoke interface: which spoke end fittings the hub is designed for, and whether the spoke hole and flange shape were drawn for those fittings specifically.
- Spoke count and lacing: matched front and rear counts, plus confirmation of the lacing patterns the flange geometry supports.
- Flange geometry: flange diameters, spoke hole offset and flange spacing, checked against the intended bracing angle and rim.
- Shell, axle and freehub materials: stated grades, not generic descriptors, since these carry the load a stiff carbon spoke transmits.
- Freehub standard: Shimano HG, Micro Spline or SRAM XD, matched to the drivetrain the wheelset will be sold with. The MT-116F/R is stated as compatible with all three.
- Brake interface and spacing: Center Lock disc interface, with 15×110mm front and 12×148mm rear Boost spacing on this hub set—confirm these match the frame and fork the wheel program targets.
- Engagement and weight: ratchet tooth count and system weight are specification points to record and compare, not performance guarantees. ARC lists the MT-116F/R at approximately 340.1g.
Working through this list before sampling turns a vague "is this hub suitable?" question into a set of specific confirmations, each of which a supplier should be able to answer from design documentation.
Working With a Hub Partner on a Carbon-Spoke Program
A carbon-spoke wheelset is a system, and the hub supplier is part of it. ARC provides OEM and ODM solutions for global bicycle brands, wheel manufacturers and distributors, covering MTB, road, gravel and e-bike applications—a scope broad enough to suggest the company understands program-level requirements rather than single-part orders. For a carbon-spoke MTB wheel program, that means a partner who can discuss flange geometry and spoke interface in the same conversation as freehub standards and Boost spacing.
The ARC MT-116F/R 24H Carbon-Spoke Boost Center Lock MTB Hub Set is the concrete starting point for programs in this category: a 24H front and rear hub set stated as specifically engineered for carbon-spoke applications, with a defined material build, a choice of 36T or 54T ratchet engagement, three freehub standards, Center Lock and Boost spacing. Buyers evaluating it should still confirm spoke interface details and flange drawings against their chosen carbon spoke and rim, but the specification conversation begins from a hub that was designed for the task rather than retrofitted to it.
For wheel program managers deciding whether to adapt a general-purpose hub or specify one purpose-engineered for carbon spokes, the safer path is the second. The hub sets the spoke path, carries the load and determines how repeatable the build will be at production volume. ARC's MT-116F/R is worth placing on the evaluation list for lightweight carbon-spoke MTB wheelsets, particularly where a matched 24H layout, Boost spacing and a choice of freehub standards align with the program brief—and where the next step is a documented specification review before any sample is built.
Contact Information
Company / Brand: Taicang Xiangyue Sports Equipment Co., Ltd.
Phone: +86 18262669919
Email: [email protected]
Official Website: www.arc-china.com
Address: No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China