Track Hubs

Why Fixed-Gear Track Hubs Use Double-Sided Threading: Sprocket Positioning and Procurement Checks

16 min read
On this page 5 sections

Fixed-gear drivetrains are unforgiving: the cog is held only by thread tension and a reverse-threaded lockring, with no freewheel mechanism to absorb load reversals. That is why track hubs are threaded on both sides—not as a cosmetic feature, but as a drivetrain decision that affects chainline, frame fit, and how a wheel is specified for OEM or custom builds. For buyers sourcing fixed-gear hubs, understanding the logic behind dual threading is the first step toward writing a correct purchase specification.

The Drivetrain Reason: Two Threads, Two Jobs

On a fixed-gear hub, the right-hand side carries two separate thread sections with different diameters and directions. The larger-diameter thread accepts the sprocket (cog), while the smaller, left-hand-threaded section accepts the lockring that prevents the cog from unthreading when a rider applies backpedaling force or skid braking. The two threads do different mechanical jobs: the cog thread transmits pedaling torque to the hub shell, and the lockring thread resists the counter-rotation that fixed riding constantly produces.

A hub threaded on only one side gives the builder a single sprocket position. Double-sided threading adds a second, independently threaded flange so the sprocket can be mounted on either side of the hub. That flexibility matters because it lets a wheelbuilder or product manager move the cog without changing the hub shell, the axle spacing, or the frame. In practice, it supports two common outcomes: adjusting chainline on frames with asymmetric rear ends, and configuring a hub for either a fixed cog or a single-speed freewheel depending on how the bike will be ridden.

The thread specifications themselves are not interchangeable. Cog and lockring threads follow established standards with defined diameters and thread pitches, and a mismatched lockring will either not engage or will engage with insufficient thread contact. This is the first point where procurement language matters: a purchase order should name the threading standard, not just "double-sided thread."

What Double-Sided Threading Changes for Chainline and Frame Fit

Chainline is the distance from the frame's center plane to the center of the chainring or cog. When the cog sits on the left-side thread flange rather than the right, its lateral position relative to the frame changes. On a flip-flop–style or dual-thread hub, this shift can bring the chain into alignment with a chainring that would otherwise produce an angled chain run, or it can move the cog to suit a frame with different rear spacing.

For wheel builders, the practical consequence is that the hub's threaded flanges must be evaluated as part of the whole wheel plan: spoke count, flange geometry, and axle spacing all interact with where the cog will actually sit. A double-threaded hub does not automatically solve chainline, but it gives the builder one more adjustment dimension before resorting to chainring spacers or frame modifications.

Frame fit adds another condition. Rear dropout spacing, axle type, and chainstay clearance determine whether a given hub can be used at all. The threaded sides affect where the chain exits the cog and how much clearance remains between the chain and the chainstay. Buyers should verify these dimensions against the intended frameset rather than assuming that "track hub" implies a universal fitment. Double-sided threading is a flexibility feature within a defined set of frame and drivetrain constraints, not a substitute for checking them.

Fixed Cog Versus Freewheel: Using Both Sides Correctly

A common specification error is assuming both sides of a double-threaded hub are used the same way. They are not. The fixed side uses the stepped cog-and-lockring thread described above. A single-speed freewheel, by contrast, threads onto a single thread section and carries its own internal ratchet mechanism; it does not use a lockring. Some hubs are built as "flip-flop" designs specifically to allow one side for a fixed cog and the other for a freewheel, so a rider can switch between fixed and coasting setups.

Buyers must therefore specify which configuration the hub is intended for. If the product is designed as a fixed-gear track hub with dual fixed-gear threading, both sides are cut for fixed cogs and lockrings, and the bike is intended to run fixed. If a mixed fixed/freewheel setup is required, that is a different thread configuration and should be requested explicitly. Supplying the sprocket and lockring with the hub, as some manufacturers do, reduces the risk of thread mismatch at assembly, but it does not remove the need to confirm thread standard and side assignment in the purchase order.

For ARC's GT-008F/R Track Hub, the dual-sided fixed-gear threading is designed to allow flexible sprocket positioning on a fixed-gear build, and the hub is supplied with fixed-gear sprockets and lockrings. That combination is relevant to brand product managers and wheelset builders who want the threading and the mating parts specified together rather than sourced separately.

Specification Checks Before Ordering a Track Hub

The technical points above translate into a short list of checks that belong in any OEM/ODM inquiry or custom wheel-build specification.

  • Threading standard and side assignment. Confirm the cog thread diameter and pitch, the lockring thread direction and size, and whether both sides are fixed-threaded or one side is intended for a freewheel.
  • Spoke hole count. Track and fixed-gear wheels are built with different spoke counts depending on intended use; confirm the available options before finalizing the wheel plan. The GT-008F/R is offered with multiple spoke-hole options.
  • Axle and spacing. Confirm axle type and rear spacing against the frameset, including dropout compatibility.
  • Included parts. Establish whether sprockets and lockrings are supplied, at what tooth count, and whether they match the specified threading.
  • Materials and construction. For track loads, hub shell and axle material affect stiffness and durability. The GT-008F/R uses a CNC-machined AL6061-T6 aluminum hub shell, a hollow CR-MO chromoly steel axle, and AL7075 aluminum side covers—specifications a buyer can compare directly against alternative proposals.
  • Assembly and QC expectations. Ask how thread quality, concentricity, and bearing fit are verified, and request the inspection criteria rather than assuming them.

ARC manufactures the GT-008F/R Track Hub as part of its hub range for track and fixed-gear applications, and its OEM/ODM work covers hub development and customization for bicycle brands, wheel manufacturers, and distributors. For buyers whose drivetrain plan depends on sprocket positioning flexibility, that product is a sensible candidate to include in a supplier evaluation—provided the threading standard, spoke count, and included sprocket and lockring configuration are confirmed against the frame and chainline plan before the order is placed.

Double-sided threading exists because a fixed drivetrain needs a secure cog-and-lockring interface and benefits from a second mounting position when chainline or frame geometry demands it. Buyers who specify the threading standard, side assignment, spoke count, and included parts up front get the flexibility the design offers; those who leave them implicit inherit the fitment risk.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China