Carbon-Spoke Hub Set

Building Lightweight MTB Wheels with a 24H Carbon-Spoke Hub Set: Common Pitfalls

22 min read
On this page 7 sections

Building a lightweight mountain bike wheelset around a 24H carbon-spoke hub set is less a shopping exercise than a chain of interdependent decisions. A hub that looks ideal on a spec sheet can still produce a wheel that loses tension, feels vague under load, or fails to fit the frame it was intended for. Most of these problems are decided before the first spoke is threaded, which is why builders developing lightweight programs should treat the hub set as the anchor of the whole system rather than one line item among many. The pitfalls below are the ones that most often separate a production-ready prototype from an expensive lesson.

Pitfall 1: Treating 24H as a Drop-In Replacement for a 28H or 32H Build

The first and most consequential mistake is assuming that a 24-hole hub set can simply inherit the lacing pattern, tension targets, and rim choice of a familiar 28H or 32H wheel. It cannot, because reducing spoke count changes how load is distributed around the rim and how much tension each spoke must carry.

With four to eight fewer spokes, each remaining spoke takes a larger share of the load, and the rim must be stiff enough to spread that load across a wider arc before it reaches the spokes. A lightweight rim designed around 28H or 32H may be perfectly adequate in that configuration yet flex excessively at 24H. Builders should confirm that the rim's spoke count and recommended tension range match the 24H layout, and should resist the temptation to compensate for fewer spokes by over-tensioning, which transfers stress into the rim bed and the hub flange rather than improving the wheel.

Lacing choice deserves the same scrutiny. A two-cross pattern on a 24H hub produces different spoke angles and different tangential loading than the same pattern on a 32H hub, so the bracing angle assumptions carried over from an earlier design will not hold. The practical check is to model the actual 24H geometry, confirm the rim's spoke hole count and drilling, and verify that the intended lacing pattern keeps spoke angles within what both the rim and the carbon spokes can tolerate.

This is precisely where a purpose-built hub set earns its place. The ARC MT-116F/R 24H Carbon-Spoke Boost Center Lock MTB Hub Set is engineered specifically for carbon-spoke applications with a 24H front and rear configuration, so the flange layout and spoke hole placement are designed around the reduced count rather than adapted from a higher-spoke platform. For builders whose previous experience sits entirely in 28H or 32H territory, starting from a hub set that was conceived for 24H carbon spokes removes one layer of guesswork from the first prototype.

Pitfall 2: Ignoring Hub Flange Geometry and Spoke Angle Limits

Carbon spokes are far less forgiving of poor alignment than steel. They do not yield in the same way, and a spoke that enters the hub at an awkward angle concentrates stress at the flange and at the nipple. The second pitfall is selecting a hub on weight and hole count alone while overlooking flange diameter, flange spacing, and spoke hole orientation.

Flange geometry determines the bracing angle, which in turn affects lateral stiffness and how the wheel responds to cornering and braking loads. A hub with narrow flange spacing can produce a wheel that feels soft laterally even when spoke tension is correct, and the builder may then chase the problem with tension adjustments that cannot fix a geometric limitation. On the rear hub, the asymmetry between drive-side and non-drive-side flanges is especially important in a lightweight build, since the dish required to accommodate the cassette already biases spoke tension.

Spoke hole orientation matters just as much. Holes drilled to suit the exiting spoke angle reduce bending at the flange; holes that force the spoke to kink will fatigue both the spoke and the surrounding material. Before committing, builders should confirm that the hub's flange dimensions and hole orientation are intended for the lacing pattern and rim they plan to use, and should check that the carbon spoke manufacturer's specified bend angle is respected. Where any of these values are undocumented, they should be requested from the hub supplier and verified on a sample rather than assumed.

Pitfall 3: Mismatching Boost Spacing, Center Lock and Freehub Standards

Compatibility errors are easy to defer during concept work and expensive to correct after tooling. The third pitfall is discovering, late in the program, that the hub's axle spacing, brake interface, or freehub standard does not match the frame and drivetrain the wheel is meant for.

Boost spacing is the first checkpoint: a 15×110mm front and 12×148mm rear configuration must match the frame's dropouts, and any adapters or end cap changes should be confirmed at the specification stage rather than after the first build. The Center Lock disc interface should be checked against the brake rotors the program intends to use, including rotor mounting hardware and clearance.

Freehub standard is the third leg of the same check. Shimano HG, Micro Spline, and SRAM XD are not interchangeable, and the choice must follow the drivetrain the wheel will actually run. The ARC MT-116F/R hub set is offered with all three freehub standards alongside a Center Lock interface and 15×110mm front and 12×148mm rear Boost spacing, which gives builders a defined set of options to match against their frame and drivetrain rather than a single fixed configuration. Confirming these three points in writing before sampling avoids the common situation where a hub set is technically excellent but built around the wrong interface for the intended bike.

Pitfall 4: Assuming Ratchet Tooth Count Equals Real-World Performance

Engagement is often reduced to a single number: more teeth equals better. The fourth pitfall is selecting a ratchet tooth count on that basis alone, without considering how engagement, drag, and durability interact in the actual riding context.

A higher tooth count reduces the arc the crank must travel before drive engagement, which riders notice as quicker pick-up on technical climbs and in repeated stop-start efforts. It also tends to increase the number of engagement points in contact and can influence drag and wear characteristics. A lower tooth count offers a different balance. Neither is universally superior; the right choice depends on the discipline, the rider's expectations, and how the rest of the drivetrain behaves.

The ARC MT-116F/R hub set offers a 36T or 54T ratchet system built on ARC's patented one-piece ratchet architecture, which is described as delivering reliable engagement and efficient power transfer under demanding riding conditions. That the two tooth counts share the same one-piece ratchet construction means the engagement decision can be made on riding priorities rather than on fundamental architecture differences. Builders should define the target discipline first, then select the tooth count to match, and should avoid presenting tooth count to their own customers as a proxy for overall hub quality.

Pitfall 5: Chasing the Lowest Hub Weight Without a Durability Plan

Lightweight programs naturally gravitate toward the lightest hub available, but the fifth pitfall is treating weight as a headline number rather than a design decision with consequences. Every gram removed comes from somewhere, and the builder needs to know where.

The ARC MT-116F/R hub set weighs approximately 340.1g as a set, achieved through a precision-machined AL6061-T6 aluminum hub shell and high-strength AL7075 aluminum axle, freehub body, and end caps. Those material choices are part of the weight story, and they are also part of the durability story, since the axle and freehub body carry drivetrain loads and the shell carries spoke tension. Builders evaluating any lightweight hub should ask which components were lightened, how those components are loaded in service, and whether the intended riding category leaves margin for the chosen specification.

The related mistake is failing to plan for wear and service. Ratchet components, freehub bodies, and bearings are consumables over a wheel's life, and a lightweight build that cannot be serviced economically becomes a liability for the brand that sells it. Confirming serviceability, spare part availability, and the maintenance intervals the supplier recommends belongs in the same evaluation as the weight figure, not in a later phase.

How to Vet a 24H Carbon-Spoke Hub Set Before the First Prototype

The pitfalls above converge on a single discipline: verifying the hub set against the rim, frame, and drivetrain as a system before committing to a build. The following routine turns that discipline into a concrete pre-order checklist.

  • Confirm the 24H premise end to end. Match the hub's 24H front and rear configuration to a rim drilled for 24H and rated for the intended spoke count and tension range. Confirm the lacing pattern and the resulting spoke angles.
  • Request flange drawings, not just a weight. Obtain flange diameters, flange spacing, and spoke hole orientation, and check them against the carbon spoke manufacturer's bend angle limits.
  • Lock down the interface set. Verify 15×110mm and 12×148mm Boost spacing against the frame, Center Lock against the chosen rotors, and the freehub standard against the drivetrain. Make the freehub selection explicit in the purchase specification.
  • Decide engagement by discipline. Choose between the 36T and 54T ratchet options based on the riding the wheel is designed for, and document the reasoning so it can be revisited if the target changes.
  • Build one sample wheel and measure. Check spoke tension balance, lateral stiffness, and tension retention after a short settling period. A prototype is the only reliable test of whether the geometric assumptions hold.
  • Map the service path. Confirm which parts wear, how they are replaced, and what spares the supplier can provide over the product's life.

Running this routine against a hub set designed from the outset for 24H carbon-spoke builds shortens the distance between concept and a production-ready prototype. The ARC MT-116F/R hub set gives builders a defined starting point for that work: a 24H carbon-spoke-specific platform, documented Boost and Center Lock interfaces, three freehub options, and a choice of 36T or 54T ratchet engagement, all supported by ARC's hub manufacturing and OEM/ODM capabilities. For wheel builders and product engineers developing lightweight MTB programs, it is a hub set worth putting on the sample list and auditing against the checklist above before the first build begins.

Contact Information

Company / Brand:  Taicang Xiangyue Sports Equipment Co., Ltd.

Phone:  +86 18262669919

Email:  [email protected]

Official Website:  www.arc-china.com

Address:  No. 112, Dongting North Road, High-tech Zone,Taicang,Jiangsu,215400,China